Daikin RXL25G2V1B Service Manual Download Page 99

Page: 99 / 294

Troubleshooting

SiENBE04-925_A

Service Diagnosis

4.8

Outdoor Unit PCB Abnormality

Remote Control
Display

Method of
Malfunction
Detection

The system follows the microprocessor program as specified.

The system checks to see if the zero-cross signal comes in properly.

Malfunction
Decision
Conditions

The microprocessor program runs out of control.

The zero-cross signal is not detected.

Supposed
Causes

Defective outdoor unit PCB

Broken harness between PCBs

Noise

Momentary fall of voltage

Momentary power failure, etc.

Troubleshooting

20/35 class

Caution

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

YES

(R12161)

YES

Replace the outdoor unit
PCB.

Ground the system.

Zero-cross signal
abnormality.
Replace the outdoor unit
PCB (1).

Replace the harness.

Check to see if the outdoor unit is
grounded.

Is LED A blinking?

Grounded?

Is the harness

broken?

Turn on the power again.

∗

Before you check the LED A,

cancel the standby electricity
saving function by operating
fan operation with the remote
control.

∗

Wait at least for 7 sec. after

turning on the power.

SIENBE04-925_A_FRONT.pdf 99

24/02/2011 13:53:56

Summary of Contents for RXL25G2V1B







































































































































































































































































































Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands

Daikin RXL25G2V1B, Service Manual

Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands