Daikin RXL25G2V1B Service Manual Download Page 103

Page: 103 / 294

Troubleshooting

SiENBE04-925_A

Service Diagnosis

4.11 DC Fan Lock

Remote Control
Display

Method of
Malfunction
Detection

An error is determined with the high-voltage fan motor rotation speed detected by the Hall IC.

Malfunction
Decision
Conditions

The fan does not start in 15 ~ 60 seconds (depending on the model) even when the fan
motor is running.

If the error repeats 16 times, the system is shut down.

Reset condition: Continuous run for about 11 minutes (35 class: 5 minutes) without any
other error

Supposed
Causes

Disconnection of the fan motor

Foreign matters stuck in the fan

Defective fan motor

Defective outdoor unit PCB

Troubleshooting

Check No.15

Refer to P.124

(R11708)

Caution

YES

Turn on the power.

Rotate the fan.

Check No. 15

Check the rotation pulse input on
the outdoor unit PCB.

Turn off the power and
reconnect the connector.

Remove them.

Replace the outdoor fan
motor.

Replace the outdoor unit
PCB.

Fan motor

connector disconnected?

Foreign matters

in or around the fan?

Replace the outdoor fan
motor.

Fan rotates

smoothly?

Pulse signal

generated?

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

SIENBE04-925_A_FRONT.pdf 103

24/02/2011 13:53:56

Summary of Contents for RXL25G2V1B







































































































































































































































































































Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands

Daikin RXL25G2V1B, Service Manual

Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands