Daikin RXL25G2V1B Service Manual Download Page 114

Page: 114 / 294

SiENBE04-925_A

Troubleshooting

Service Diagnosis

Troubleshooting

20/25 class

Check No.29

Refer to P.125

Caution

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

YES

Turn off the power.

Check the connection.

Check the power supply voltage.

Correct the power supply.

Voltage as

rated?

(R11380)

YES

Check No. 29

Check the short circuit of the diode
bridge.

Check with the inverter checker (

∗

Turn off the power. Disconnect the
harnesses U, V, and W.

Turn on the power.
Check the electrolytic capacitor
voltage.

Electrical

components or

compressor harnesses

connected as

specified?

Replace the outdoor unit
PCB.

Replace the compressor.

Correct the power supply or
replace the outdoor unit
PCB.

Reconnect them as
specified.

Replace the outdoor unit
PCB or the outdoor fan.

∗

Inverter checker

Part No.: 1225477

Normal?

320 ± 50 VDC?

Any LED OFF?

SIENBE04-925_A_FRONT.pdf 114

24/02/2011 13:53:57

Summary of Contents for RXL25G2V1B







































































































































































































































































































Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands

Daikin RXL25G2V1B, Service Manual

Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands