manualshive.com logo in svg

Daikin RXL25G2V1B, Service Manual

Share
Download
Daikin RXL25G2V1B Service Manual Download Page 167

Indoor Unit

SiENBE04-925_A

152

Removal Procedure

2. Remove the swing motor 

for horizontal blade.

Caution

When reassembling, do not 
confuse the installing order 
of the 2 motors and the 
colors of the connectors.
If you set the connectors or 
motors opposite, the 
horizontal blades do not 
move smoothly or the noise 
may be heard.

(1) Set the motor for the upper 

blade first.
(connector: white)

(2) Then, set the motor for the 

lower blade.
(connector: red)

(3) Fix the both motors with a 

screw.

1

Remove the screw and 
remove the swing 
motors for horizontal 
blades.

2

Disconnect the 
harnesses from the 
motors.

Step

Procedure

Points

(R8131)

Connector for 
lower blade (red)

Connector for 
upper blade (white)

Screw

(R8132)

(R10335)

SIENBE04-925_A_FRONT.pdf   167

24/02/2011   13:54:04

Summary of Contents for RXL25G2V1B







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands