manualshive.com logo in svg

Daikin RXL25G2V1B, Service Manual

Share
Download
Daikin RXL25G2V1B Service Manual Download Page 106

SiENBE04-925_A

Troubleshooting

Service Diagnosis

91

Troubleshooting

Check No.05

Refer to P.119

Check No.06

Refer to P.120

Check No.11

Refer to P.122

NG

OK

NO

OK

NG

OK

YES

NG

Correct it.

Reconnect it.

YES

YES

YES

NO

NO

Replace the outdoor unit 
PCB.

∗

 Refrigerant shortage

∗

 Water mixed

∗

 Stop valve

Replace the defective 
thermistor.

Refer to the refrigerant line 
check procedure.

Replace the four way valve 
(defective or dust-clogged).

Reconnect in position.

Caution

Be sure to turn off the power switch before connecting or disconnecting 
connectors, or parts may be damaged.

(R11710)

Four way valve 

coil disconnected (loose)?

Harness out of 

connector?

Any thermistor 
disconnected?

Check No. 06

Check the thermistors.

Check No. 11

Check the refrigerant line.

Check No. 

05

Check the four way valve 

switching output.

Check the continuity of the four way 
valve coil and harness.

Replace the four way valve 
coil.

NO

Resistance 

between harnesses 

about 1000 ~ 2000 

Ω

?

Disconnect the harness from the 
connector.

SIENBE04-925_A_FRONT.pdf   106

24/02/2011   13:53:56

Summary of Contents for RXL25G2V1B







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands