manualshive.com logo in svg

Daikin RXL25G2V1B, Service Manual

Share
Download
Daikin RXL25G2V1B Service Manual Download Page 170

SiENBE04-925_A

Indoor Unit

Removal Procedure

155

2

Loosen the lock screw 
and remove the fan 
rotor.

„

When reassembling the fan 
rotor, provide as much as 
5 mm of play between the 
side face of the rotor and the 
bottom frame. 

(1) Insert the fan motor with 

approx. 5 mm left.

(2) Tighten the screw until it 

stops. Then turn the screw 
in one scroll.

(3) Move the fan rotor and 

confirm the fan motor and 
the fan rotor are installed 
appropriately.

(4) Tighten the screw 

completely if appropriate.

(5) If not appropriate, go back to 

(1).

3

Press the bearing 
ASSY from outside.

4

Remove the bearing.

Step

Procedure

Points

(R8120)

Lock screw

Fan motor

(R2808)

Side face of rotor

Side face of 
bottom frame

5 mm

(R9582)

(R8121)

(R8122)

SIENBE04-925_A_FRONT.pdf   170

24/02/2011   13:54:04

Summary of Contents for RXL25G2V1B







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands