Daikin RXL25G2V1B Service Manual Download Page 150

Page: 150 / 294

SiENBE04-925_A

Indoor Unit

Removal Procedure

135

1.4

Removal of Horizontal Blades / Vertical Blades

Procedure

Warning

Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.

Step

Procedure

Points

1. Remove the horizontal

blade (large).

Open the horizontal
blade (large).

Caution on Mounting

Mount the large horizontal
blade to the upper side and
the small horizontal blade to
the lower side.
Do not put them in the
wrong place.

Unfasten the center
shaft while bending the
horizontal blade (large)
slightly.

Unfasten the left shaft.

Unfasten the key
alignment shaft at the
right side.

Caution on Mounting

There is a key alignment at
the right shaft. When
mounting, insert the right
shaft first while turning.

After inserting the right
shaft, mount the horizontal
blade first to the center shaft
and then to the left shaft.

(R7921)

Horizontal blade (large)

Horizontal blade (small)

(R7922)

(R7923)

(R7924)

SIENBE04-925_A_FRONT.pdf 150

24/02/2011 13:53:59

Summary of Contents for RXL25G2V1B







































































































































































































































































































Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands

Daikin RXL25G2V1B, Service Manual

Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands