manualshive.com logo in svg

Daikin RXL25G2V1B, Service Manual

Share
Download
Daikin RXL25G2V1B Service Manual Download Page 144

SiENBE04-925_A

Indoor Unit

Removal Procedure

129

3. Remove the Titanium 

apatite photocatalytic air-
purifying filter.

1

The Titanium apatite 
photocatalytic air-
purifying filter ASSY is 
attached to the back of 
the air filter.

„

The Titanium apatite 
photocatalytic air-purifying 
filter is not marked for 
difference between the right 
and left sides.

2

Remove the Titanium 
apatite photocatalytic 
air-purifying filter ASSY 
by bending the air filter 
and unfastening the 
projections from the air 
filter frame.

3

Remove the Titanium 
apatite photocatalytic 
air-purifying filter from 
its frame (at 5 positions) 
by bending it.

Step

Procedure

Points

(R7904)

Air filter

Titanium apatite 
photocatalytic 
air-purifying filter ASSY

(R7905)

Projections

(R4311)

SIENBE04-925_A_FRONT.pdf   144

24/02/2011   13:53:58

Summary of Contents for RXL25G2V1B







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands