Daikin RXL25G2V1B Service Manual Download Page 129

Page: 129 / 294

Troubleshooting

SiENBE04-925_A

114

Service Diagnosis

Troubleshooting

Check No.04

Refer to P.118

Check No.06

Refer to P.120

(R12015)

Caution

YES

∗

Discharge pipe thermistor

∗

Indoor or outdoor heat exchanger thermistor

∗

Room temperature thermistor

∗

Outdoor temperature thermistor

Check for refrigerant shortage.

Change for a specified amount of
fresh refrigerant.

Check No. 04

Electronic expansion valve

functioning?

Replace them in position.

Open the stop valve.

Repair the pipe flare or
replace the union.

Check the power transistor
harness for looseness.
Correct it as required. Also
replace the cracked pipe.

Check the pipes for
improper contact. Correct
them as required. Also
replace the cracked pipe.

Replace the electronic
expansion valve.

Replace the defective
one(s).

Completed.

Refrigerant

shortage error again?

Oil oozing at

internal piping?

Stop valve

closed?

Compressor

vibrating too much?

Oil oozing at

relay pipe connections?

Any thermistor
disconnected?

Check No. 06

Check the thermistors.

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

YES

Replace the outdoor unit PCB.

Replace the compressor.

Completed.

Error again?

SIENBE04-925_A_FRONT.pdf 129

24/02/2011 13:53:57

Summary of Contents for RXL25G2V1B







































































































































































































































































































Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands

Daikin RXL25G2V1B, Service Manual

Search results

Summary of Contents for RXL25G2V1B

Reviews:

Brands by name

Popular brands