Cypress CY8C28 series Technical Reference Manual Download Page 420 | Manualshive

Page: 420 / 571

background image

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

419

Analog Input Configuration

20.2

Register Definitions

The following registers are associated with Analog Input Configuration and are listed in address order. Each register descrip-
tion has an associated register table showing the bit structure for that register. For a complete table of the analog input config-
uration registers, refer to the

“Summary Table of the Analog Registers” on page 389

.

Depending on how many analog columns your PSoC device has (see the Cols. column in the register tables below), only cer-
tain bits are accessible to be read or written. The bits that are grayed out throughout this manual are reserved bits and are not
detailed in the register descriptions that follow. Reserved bits should always be written with a value of ‘0’.

Note

For the CY8C28x13, CY8C28x33, CY8C28x43, CY8C28x45, and CY8C28x52 PSoC devices, refer to the

Multiplexer chapter on page 525

for information on bringing that device’s analog mux bus into the analog array.

20.2.1

AMX_IN Register

The Analog Input Select Register (AMX_IN) controls the
analog muxes that feed signals in from port pins into the
analog column.

This register can only be used with four and two column
PSoC devices.

Bits 7 to 0: ACIx[1:0].

For four column PSoC devices, each of the analog columns
can have up to four port bits connected to its muxed input.
There are up to four additional analog inputs that go directly
into the Switch Capacitor PSoC blocks.

For two column PSoC devices, the ACI1[1:0] and ACI0[1:0]
bits control the analog muxes that feed signals in from port
pins into the analog column. The analog column can have
up to eight port bits connected to its muxed input. ACI1 and
ACI0 are used to select among even and odd pins. The
AC1Mux bit field controls the bits for those muxes and is
located in the Analog Output Buffer Control register
(ABF_CR0). There are up to two additional analog inputs
that go directly into the Switch Capacitor PSoC blocks.

For additional information, refer to the

AMX_IN register on

Add.

Name

Cols.

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,60h

4

ACI3[1:0]

ACI2[1:0]

ACI1[1:0]

ACI0[1:0]

RW : 00

2

ACI1[1:0]

ACI0[1:0]

«
...
418
419
420
421
422
...
»

Summary of Contents for CY8C28 series




























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CY8C28 series

Brand: MADRIX Pages: 36

Brand: Value Point Pages: 7

Brand: National Instruments Pages: 6

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: Sailor Pages: 1

Brand: U.S. Divers Pages: 22

Brand: Vega Pages: 20

by-me Eikon 20526

Brand: Vimar Pages: 6

Brand: Neets Control Pages: 12

Brand: Maverick Pages: 122

ELVOX KLYS ENM1

Brand: Vimar Pages: 24

Brand: Kilews Pages: 11

mikromedia for dsPIC3

Brand: mikroElektronika Pages: 36

Brand: Dawn Pages: 100

Brand: Thundercomm Pages: 5

Brand: EFI Pages: 129

Brand: Neptronic Pages: 2

Brand: SMSC Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands