Cypress CY8C28 series Technical Reference Manual Download Page 293 | Manualshive

Page: 293 / 571

background image

292

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

IDAC_CR1

1,DCh

13.3.72

IDAC_CR1

IDAC Control Register 1

This register contains the control bits for the IDAC current that drives the analog mux bus and for selecting the split
configuration.

For additional information, refer to the

“Register Definitions” on page 528

in the I/O Analog Multiplexer chapter.

7

EN1

0

Disables right IDAC (IDAC1).

1

Enables right IDAC (IDAC1).

6

MuxClkGE1

0

Disables driving right side MUXCLK (MUXCLK1) to GOO[7]

.

1

Enables driving right side MUXCLK (MUXCLK1) to GOO[7].

5

ICEN

0

Disables this feature: both IDAC will be controlled by their own registers, including data and
output on/off registers.

1

Enables this feature: both IDAC0 and IDAC1 will use the IDAC0_D register for IDAC current
setting when their output enable signal is high, and it will automatically switch to use
IDAC1_D register for IDAC setting when their output enable signal is low.

4:1

IDAC_TRIM[3:0]

These signals go to PLL block and are used to trim IUNIT32 current output. The default value is
1000b (ideally it is 10 µA). Each step will change the current approximately by 3%.

0

Double_Current

This bit is used for IDAC current range control; it will combine with IDAC_CR0[3].IRANGE to define
four different IDAC current range.

Double_Current

IDAC_CR0[3].IRANGE

Current Range

0 (default)

0 (default)

Reserved

1

0

Maximum 91.03 µA

0

1

Maximum 318.75 µA

1

1

Maximum 637.5 µA

Individual Register Names and Addresses:

1,DCh

IDAC_CR1 : 1,DCh

7

6

5

4

3

2

1

0

Access : POR

RW : 0 RW : 0 RW : 00

RW : 1000

RW : 0

Bit Name

EN1

MuxClkGE1

ICEN IDAC_TRIM

Double_Current

Bits

Name

Description

«
...
291
292
293
294
295
...
»

Summary of Contents for CY8C28 series




























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CY8C28 series

Brand: Ultraflex Pages: 7

Brand: maxon motor Pages: 44

Brand: Washify Pages: 25

Brand: microHAM Pages: 64

Brand: Eaton Pages: 2

Brand: RIFT Actuators Pages: 23

Brand: Troy-Bilt Pages: 11

Brand: MAKELSAN Pages: 28

FINGER007 Series

Brand: IDTECK Pages: 9

Compact GuardLogix 5370

Brand: Allen-Bradley Pages: 210

Brand: MAC3 Pages: 20

Brand: WOBIT Pages: 25

Brand: BioSmart Pages: 24

Brand: Roger Pages: 29

Brand: Silverline Pages: 2

Brand: RKC INSTRUMENT Pages: 176

KitchenGo Premium

Brand: Bematech Pages: 11

SAF VFU21 Series

Brand: Danfoss Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands