Curtiss-Wright SCRAMNet+ SC150e Hardware Reference Manual Download

Page: 18 / 140

SCRAMNET OVERVIEW

2-6

S SC150e HARDWARE REFERENCE

2.6 Interrupts

S SC150e allows a node processor to receive interrupts from and transmit

interrupts to any node on the network. This includes the originating node, provided the

receiving node is set up to receive an interrupt message. Interrupts are generated under

two different conditions:

•

S SC150e network data writes to shared memory; and

•

S SC150e network errors detected on the local node.

S SC150e

interrupts usually require a device driver to interface with the node

processor. The driver is required primarily to permit the host processor to handle

interrupts from the SCRAMNet

device.

2.6.1 Network Interrupt Writes

FOREIGN MESSAGE

The node can receive a message from another node with the interrupt bit set. If Receive

Interrupt Enable ACR[0] and Interrupt Mask Match Enable CSR0[5] are enabled, the

data is written to shared memory and the address is placed on the Interrupt FIFO.

NATIVE MESSAGE

If the message received was originated by the node, and Write Own Slot Enable CSR2[9]

and Enable Interrupt on Own Slot CSR2[10] are enabled, the host has authorized a Self-

Interrupt. The data is written to shared memory and the address is placed on the Interrupt

FIFO.
Network Interrupt writes are accomplished by two methods:

•

Selected

. Data writes to selected shared-memory locations from the network.

•

Forced

. Any data writes to any shared memory from the network.

In either case, the node can be configured to write to itself. This condition is called “Self

Interrupt”.

2.6.2 Selected Interrupt

The selected-interrupt method requires choosing S SC150e shared-memory

locations on each node to receive and/or to transmit interrupts. These shared-memory

locations may also be used to generate signals to external triggers. The procedure for

selecting shared-memory locations for interrupts and/or external triggers is explained in

the paragraph on the Auxiliary Control RAM, paragraph 2.5.

OUTGOING INTERRUPT

The Outgoing Interrupt is described in Figure 2-3. If both Transmit Interrupt Enable

ACR[1] and Network Interrupt Enable CSR0[8] are set, and a data item is transmitted to

any of the selected-interrupt memory locations, then an interrupt message is sent out on

the network. This message will generate interrupts to any processors on the network that

have that same shared-memory location selected to receive interrupts.

Summary of Contents for SCRAMNet+ SC150e





























































































































Search results

Summary of Contents for SCRAMNet+ SC150e

Reviews:

Related manuals for SCRAMNet+ SC150e

Brands by name

Popular brands

Curtiss-Wright SCRAMNet+ SC150e, Hardware Reference Manual

Search results

Summary of Contents for SCRAMNet+ SC150e

Reviews:

Related manuals for SCRAMNet+ SC150e

Brands by name

Popular brands