Comtech EF Data Vipersat SLM-5650A Installation And Operation Manual Download Page 385 | Manualshive

Page: 385 / 516

background image

SLM-5650A Satellite Modem

Revision 10

Appendix E

E–63

MN-SLM-5650A

E.7.5.8 Vipersat Pages

Consult adjunct Comtech EF Data publication MN-0000035 Vipersat SLM-
5650A Satellite Network Modem Router User Guide for configuration and
use of these optional pages.

Figure E-35 shows the NP HTTP/HTTPS Interface pages with Vipersat
installed on the SLM-5650A. Vipersat is a FAST Option which must be
purchased from Comtech EF Data. See Section E.2.5.2.2 Admin | FAST
Features for more information.

Note that if the SLM-5650A does not have the Vipersat FAST Option
installed, the hyperlinks associated with the Vipersat navigation tab will not
be visible or otherwise available to the user.

Figure E-35. Vipersat Pages

«
...
383
384
385
386
387
...
»

Summary of Contents for Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Vipersat SLM-5650A

Brand: D-Link Pages: 66

Brand: D-Link Pages: 26

Brand: D-Link Pages: 16

Brand: Sagem Pages: 4

MT5656ZDX Series

Brand: Multitech Pages: 30

Brand: ICP DAS USA Pages: 28

Brand: WePresent Pages: 71

Brand: BandLuxe Pages: 23

Brand: Synxcom Pages: 216

Brand: Commander Pages: 5

Brand: BROSTREND Pages: 13

Brand: Telecom Pages: 16

Brand: Protectli Pages: 33

Brand: Four-Faith Pages: 35

OnCell G2111 Series

Brand: Moxa Technologies Pages: 49

Brand: Settop Pages: 2

Brand: Hughes Network Pages: 4

RC802-30B-FV35-S1

Brand: Raisecom Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands