Comtech EF Data Vipersat SLM-5650A Installation And Operation Manual Download Page 91

Page: 91 / 516

SLM-5650A Satellite Modem

Revision 10

Firmware Update

5–11

MN-SLM-5650A

5.2.5

Download and Extract the Firmware Update Files

The example figures in this section are provided for reference only. Your
firmware information will be different.

Do these steps:

Step

Task

Go online to

www.comtechefdata.com.

On the Main page – Under Support Information or the Support tab, select the Software

Downloads hyperlink.

On the Flash Updates Index page – Select the (Select a Product Line) Satellite Modems

hyperlink.

On the Modems product page – Select the SLM-5650A product hyperlink.

Select the appropriate firmware archive EXE or ZIP file download hyperlink.

Once you select the EXE or ZIP hyperlink, the File Download dialogue opens on your browser and

prompts an action. You may otherwise click [Cancel] to quit the file download process. Note the

following:

For EXE files:

Click [Run] to open the self-extractor dialogue window. Use [Browse] to select your destination

folder. Click [Unzip] to extract the files. Your results display as per this example – click [OK] to

close. Your files are now available for transfer to the modem.

Summary of Contents for Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vipersat SLM-5650A

Reviews:

Related manuals for Vipersat SLM-5650A

Brands by name

Popular brands

Comtech EF Data Vipersat SLM-5650A, Installation And Operation Manual

Search results

Summary of Contents for Vipersat SLM-5650A

Reviews:

Related manuals for Vipersat SLM-5650A

Brands by name

Popular brands