Comtech EF Data Vipersat SLM-5650A Installation And Operation Manual Download Page 465

Page: 465 / 516

SLM-5650A Satellite Modem

Revision 10

Appendix F

F–41

MN-SLM-5650A

F.5.3.5 Firmware [F]

Chapter 5. FIRMWARE UPDATE

See

Chapter 5. FIRMWARE UPDATE

for detailed information on the procedures associated with

the TRANSEC Module firmware update process.

Figure F-24. Firmware (Unit Info) Menu Page

Table F-13. Firmware (Unit Info) Menu Options

Menu Options/Fields

Entry

Description

Bootrom Info

[RO] Displays the bootrom firmware.

Bulk 1 Info

[RO] Displays the firmware version loaded into the Slot 1 location.

Bulk 2 Info

[RO] Displays the firmware version loaded into the Slot 2 location.

Boot From

Selects the firmware boot source for modem operations as follows:
0 – Newest (automatically selects the most current version firmware residing

in either Slot 1 or Slot 2);
1 – Slot 1 (selects the firmware residing in the Slot 1 location;

2 – Slot 2 (selects the firmware residing in the Slot 2 location.

If the ‘Boot From’ selection is changed, you must reboot the

modem in order for that firmware selection to be loaded for

operation.

Summary of Contents for Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vipersat SLM-5650A

Reviews:

Related manuals for Vipersat SLM-5650A

Brands by name

Popular brands

Comtech EF Data Vipersat SLM-5650A, Installation And Operation Manual

Search results

Summary of Contents for Vipersat SLM-5650A

Reviews:

Related manuals for Vipersat SLM-5650A

Brands by name

Popular brands