Comtech EF Data Vipersat SLM-5650A Installation And Operation Manual Download Page 311 | Manualshive

Page: 311 / 516

background image

SLM-5650A Satellite Modem

Revision 10

Appendix D

D–7

MN-SLM-5650A

D.2.4

10/100/1000 BaseT (GbE) Interface Module Removal and

Installation

WARNING!
Make sure that the unit is POWERED OFF. Serious injury or damage to the
equipment could result if the unit is powered during module removal or
installation! You must take care not to damage the module’s components
during removal or installation.

Figure D-4. GbE Interface Module Removal or Installation

D.2.4.1.1

GbE Interface Module Removal Procedure

Step

Task

1

Turn off the power to the modem.

2

Disconnect the RJ-45 cable from the Interface Module.

3

Loosen the (two) captive screws securing the module to the chassis.

4

Pull the module straight out until it is clear of the chassis slot.

D.2.4.1.2

GbE Interface Module Installation Procedure

Step

Task

1

Insert the Interface Module straight into the slot, using the chassis’ internal card guides, until it plugs

securely into the internal card receptacle.

2

Secure the module to the chassis using the (two) captive screws.

3

Connect the RJ-45 cable to the Interface Module.

4

Turn on the power to the modem.

«
...
309
310
311
312
313
...
»

Summary of Contents for Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Vipersat SLM-5650A

Brand: Maestro Pages: 4

Brand: RACOM Pages: 157

FSMODEM-CELLBASE

Brand: Federal Signal Corporation Pages: 16

Brand: Whirlwind Pages: 16

Brand: TCAM Pages: 47

Brand: nawras Pages: 29

DirecWay DW4020

Brand: Hughes Network Pages: 102

Barricade SMC7904BRA2

Brand: SMC Networks Pages: 2

Brand: TP-Link Pages: 122

Brand: H3 System Pages: 15

Brand: DOUXE Pages: 9

Brand: Comrex Pages: 14

Brand: M2M Pages: 32

Brand: Four-Faith Pages: 48

Brand: TRENDnet Pages: 96

Brand: US Robotics Pages: 2

Brand: US Robotics Pages: 4

Brand: US Robotics Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands