manualshive.com logo in svg

Comtech EF Data Vipersat SLM-5650A, Installation And Operation Manual

Share
Download
Comtech EF Data Vipersat SLM-5650A Installation And Operation Manual Download Page 368

 

SLM-5650A Satellite Modem 

 

Revision 10 

 

Appendix E 

E–46 

MN-SLM-5650A 

E.7.5.5.3 

WAN | Loopback Test 

Use this page to test the operational integrity of the NP Interface M&C, WAN Interface, and IF 
Interface. 

 

 

Figure E-26. WAN | Loopback Test Page 

 

Loopback Test 

Loopback Test Results 

– This message window displays the results of the completed Loopback 

Test. 

Packet Loopback Test 

– When you click 

[Start Test], 

the NP Interface sends 50 multicast packets 

towards the WAN interface, and enables the IF Loopback. All packets returned from the IP 
Loopback will count by the NP Interface, and are displayed in the Packet Loopback Test Results 
window. 

 

 

Summary of Contents for Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands