Comtech EF Data Vipersat SLM-5650A Installation And Operation Manual Download Page 345 | Manualshive

Page: 345 / 516

background image

SLM-5650A Satellite Modem

Revision 10

Appendix E

E–23

MN-SLM-5650A

E.7.5.2.4

Admin | SNMP

Chapter 8. ETHERNET INTERFACE OPERATION

The Admin user may use this page to change the parameters associated with Simple Network
Management Protocol, an application-layer protocol designed to facilitate the exchange of
management information between network devices. The SLM-5650A SNMP agent supports
SNMPv1, SNMP v2c, and SNMP v3. See

Chapter 8. ETHERNET INTERFACE OPERATION,

Sect. 8.4

SNMP Interface, for complete details on SNMP and using this page.

Figure E-10. Admin | SNMP Page

SNMP

The SNMP Read and Write Communities cannot be changed; the default name for Read
Community is

public

; the default Write Community name is

private

.

Click

[Submit]

to enable the SNMP configuration changes made to

Trap Community

,

Trap

,

System Contact

, and

System Location

.

«
...
343
344
345
346
347
...
»

Summary of Contents for Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Vipersat SLM-5650A

Digital Business System

Brand: Panasonic Pages: 58

Brand: C-Data Pages: 34

Brand: Data-Linc Group Pages: 19

Brand: DataComm Pages: 39

Brand: ESTeem Pages: 78

Brand: GDI COMMUNICATIONS Pages: 31

Myriad MD9612FP

Brand: Raymar Pages: 33

Brand: Adeunis RF Pages: 27

Brand: Adeunis RF Pages: 50

Brand: 3Jtech Pages: 4

Brand: 3Jtech Pages: 27

EZ Connect SMC8002CM-US

Brand: SMC Networks Pages: 2

EZ Connect SMC8004CM

Brand: SMC Networks Pages: 2

EZ Connect SMC7003-USB

Brand: SMC Networks Pages: 70

Brand: Zoom Pages: 66

DM111Pv2 - ADSL2+ Ethernet Modem

Brand: NETGEAR Pages: 26

Brand: Picosens Pages: 9

819-GPRS series

Brand: CalAmp Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands