manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 75 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 75

ID-FLX Lite Global Guide

75

6 Troubleshooting

6.1 Alarm management

75

6.2 History file

78

6.3 Diagnostic messages read from ECU

79

6.4 Tier 4 diagnostic codes

81

6

back to Table of contents

6.1 Alarm management

Following alarms are available:

Sensor fail

Warning

Cooldown

Shut down

Note:

Type of protection for binary and analog inputs is adjustable in PC tool LiteEdit. In window Modify after

double click on input adjust Alarm type.

6.1.1 Sensor fail (Fls)

Sensor fail is detected when measured value is 6 % out of selected sensor characteristic. Sensor fail is

indicated by ##### symbol instead of measured value.

6.1.2 Warning (Wrn)

When warning comes up, only alarm outputs and common warning output are closed.

Note:

For list of possible warning alarms

see List of possible alarms on page 76

.

6.1.3 Cooldown (Cd)

When cooldown comes up, engine is stoped slowly over cooling state.

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments