manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 113 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 113

ID-FLX Lite Global Guide

113

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[-]

Default value

-

Step

-

Comm object

24367

Related applications

Description

E-mail address used as “Sender” of alarm e-mails from IB-Lite.

Note:

If SMTP server requires verification of sender, e-mail address has to be registered to SMTP server

and setpoints “SMTP UserName” and “SMTP UserPass” has to be set to correct values.

Contr MailBox

6

back to List of setpoints

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[-]

Default value

-

Step

-

Comm object

24366

Related applications

Description

List of time zones used for time reference.

Time Zone

6

back to List of setpoints

Setpoint group

Communication

Settings

Related FW

2.5.0

Range [units]

[-]

Default value

-

Step

-

Comm object

24362

Related applications

Description

This is IP address of Domain Name Server.

DNS IP Address

6

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments