ComAp InteliDrive FLX LITE Manual Download Page 67

Page: 67 / 228

ID-FLX Lite Global Guide

Input

Analog input

CU: AI1-AI9

AIO: AI1-AI4

Binary input

LoadRequest2

LoadRegDisable

(optional)

Binary input

RegRequest2

R Reg Disable

(optional)

Output

Analog output

Load Limit

ByRPMCtrlAout

(plug-in module)

Setpoints

Load limit

Load Input = Load

Load Bias

Load Request 1

Load Request 2

Load ReqRamp

Load UpLimit

Load DownLimit

Load Gain

Load Integral

Regulator

Reg Input

Reg Bias

Request

Request 2

Reg Gain

Reg Integral

Engine load limitation with analog output

Purpose: Protect the engine against overload by reducing the load.

Description: The engine load (e.g. feeder speed) is reduced when actual “Percentual load” (coming from ECU) is

over the

LoadRequest 1 (page 136)

(or

Load request 2 (page 136)

) setpoint. Load can be continuously

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 67 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: