ComAp InteliDrive FLX LITE Manual Download Page 169

Page: 169 / 228

ID-FLX Lite Global Guide

169

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

NONE, MONDAY, TUESDAY, WEDNESDAY, THURSDAY, WEDNESDAY,

FRIDAY, SATURDAY, SUNDAY, MON-FRI, MON-SAT, MON-SUN, SAT-SUN [-]

Default value

NONE

Step

Comm object

10045

Related applications

Description

This setpoint defines

activation.

is internally linked with

. Refer to binary inputs for details.

NONE

Timer function is disabled. Default state.

MONDAY, TUESDAY, WEDNESDAY,

THURSDAY, WEDNESDAY, FRIDAY,

SATURDAY, SUNDAY

Timer is activated on daily basis.

MON-FRI, MON-SAT, SAT-SUN

Timer is activated on selected day interval.

Timer1repeat

back to List of setpoints

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

[HH:MM:SS]

Default value

Step

Comm object

10042

Related applications

Description

Display day time when Timer 1 output is activated.

Timer1 ON time

back to List of setpoints

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

1 .. 1440 [min]

Default value

Step

Comm object

10044

Related applications

Description

Adjusts duration of Timer 1 output.

Timer1Duration

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 169 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: