manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 189 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 189

ID-FLX Lite Global Guide

189

Related FW

2.5.0

Related applications

Comm object

184

Description

Binary input has no function. Use this option when binary input is not connected.

Not used

6

back to List of LBI

Related FW

2.5.0

Related applications

Comm object

172

Description

Binary input is used for external request for engine run in AUT mode only.

Rem start/stop

6

back to List of LBI

Related FW

2.5.0

Related applications

Comm object

40

Description

If the input is opened, shut down is immediately activated. Input is inverted (normally closed) in default

configuration.

Note:

In case of controller hardware or software fail, safe stop of the engine doesn’t have to be ensured.

To back-up the Emergency stop function it is recommended to connect separate circuit for disconnection

of Fuel solenoid and Starter signals.

Emergency stop

6

back to List of LBI

Related FW

2.5.0

Related applications

Comm object

44

Description

If the input is closed all alarms are disabled except the binary input Emergency stop and "engine overspeed

protection".

All ID-Lite alarms are detected,

ID-Lite front panel RED LED blinks or lights,

Alarm is recorded on the ID-Lite alarm list screen,

BUT engine remains running.

Note:

Warning SprinklActive is indicated in the Alarm list if sprinkler mode active to inform the operator

that the engine is not protected.

Sprinkler

6

back to List of LBI

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments