manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 200 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 200

ID-FLX Lite Global Guide

200

Related FW

2.5.0

Related applications

Comm object

24

Description

Closed relay energizes the starter of engine.

The relay opens if:

The strating speed is reached or

Maximum time of cranking is exceeded or

Request to stop comes up

Starter

6

back to List of LBO

Related FW

2.5.0

Related applications

Comm object

22

Description

Closed output opens the fuel solenoid and enables the engine start.

The output opens if:

Emergency stop comes or

Cooled engine is stopped or

In pause between repeated starts

Fuel solenoid

6

back to List of LBO

Related FW

2.5.0

Related applications

Comm object

23

Description

The closed output energizes stop solenoid to stop the engine.

The output is active at least for Stop time, if the stop lasts longer; it stays active until all symptoms say the

engine is stopped.

The engine is stopped if:

RPM < 2 and

Oil pressure <

Starting POil (page 114)

Note:

The engine can be started anytime, if all symptoms say the engine is steady regardless of the fact

the Stop solenoid can still be active (in that case it is deactivated before cranking).

Note:

In case when stop time period is lower than "stop engine detected" + 10 s, stop time period is

extended to this value due to safety reason. (stop engine detected = RPM<2, OilP not detected, D+ not

active)

Stop solenoid

6

back to List of LBO

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments