ComAp InteliDrive FLX LITE Manual Download Page 226

Page: 226 / 228

ID-FLX Lite Global Guide

226

10.2.1 IL-NT RS232 (optional card)

Plug-in into ID-Lite controller COMMUNICATION MODULE port.

Maximal distance

10 m

Speed

19.2 kBd (STD)

9.6 kBd (MODBUS)

Recommend external converter:

ADVANTECH – ADAM 4520: RS232 to RS232/RS485converter, DIN rail, automatic RS485 bus supervision,

no external data flow control signals, galvanic isolated.

Recommended internal converter:

ADVANTECH – PCL-745B or PCL745S : Dual port RS232/RS485 Interface card, automatic RS485 bus

supervision, no external data flow control signals, galvanic isolated.

10.2.2 IL-NT RS232/485 (optional card)

Plug-in into InteliDrive Lite controller COMMUNICATION MODULE port.

Maximal

distance

10 m (RS232), 1200 m (RS485)

Speed

Up to 57.6 kBd (DIRECT), 38.4kBd Analog modem, 9.6 kBd digital modem, 57.6 kBd

(MODBUS)

10.2.3 IL-NT S-USB (optional card)

Plug-in into ID-Lite controller COMMUNICATION MODULE port.

Maximal

distance

5 m

Speed

Up to 57.6 kBd (DIRECT), 38.4 kBd Analog modem, 9.6 kBd digital modem, 57.6 kBd

(MODBUS)

Use only shielded A-B USB cables up to 5 m length.

Recommend USB cable:

USB-LINK CABLE 1.8M - ComAp A-B USB cable.

10.2.4 IB-Lite (optional card)

Plug-in into ID-Lite controller COMMUNICATION MODULE port.

10/100 MBit Ethernet interface in RJ45 socket.

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 226 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: