ComAp InteliDrive FLX LITE Manual Download Page 129

Page: 129 / 228

ID-FLX Lite Global Guide

129

Group: Regulator

Setpoint group

Load limit

Related FW

2.5.0

Range [units]

OFF, CU:AI1, CU:AI2, CU:AI3, CU:AI4, CU:AI5, CU:AI6, CU:AI7, CU:AI8, CU:AI9,

AIO:IA1, AIO:AI2, AIO:AI3, AIO:AI4 [-]

Default value

YES

Step

Comm object

11842

Related applications

Description

Setpoint is determined for selection of analog input for Speed request in the controller’s MAN mode.

OFF

Speed request selection is done by binary inputs. Default state.

CU: AI1-CU: AI9 Speed request via analog input of the controller only. Binary inputs are ignored.

AIO :1-AIO4

Speed request via analog input of extension module IL-NT-AIO only. Binary inputs are

ignored.

Note:

Analog speed request is ignored in AUT mode.

Note:

See

Speed request chart (page 64)

LAI SpdRequest

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 129 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: