ComAp InteliDrive FLX LITE Manual Download Page 168

Page: 168 / 228

ID-FLX Lite Global Guide

168

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

[DD:MM:YYYY]

Default value

Step

Comm object

24553

Related applications

Description

Actual date.

Date

back to List of setpoints

Setpoint group

Date/Time

Related FW

2.5.0

Range [units]

NoFunc, AutoRun, AutoRegCMP, AutoBatt, AutoStop [-]

Default value

No Func

Step

Comm object

11660

Related applications

Description

No Func

Operates just corresponding

according the

setting, see

Timer1repeat (page 169)

Timer1 ON time (page 169)

Timer1Duration

(page 169)

. Function operates in all OFF-MAN-AUT modes. Default state.

AutoRun

Engine automatically starts and stops in AUT mode (similar to

, the same record in the history) according the

setting.

AutoRegCMP

Start and stop engine in AUT mode according to the

- see

CMP Input (page 133)

. The comparator function (output) works opposite when

Reg

CMP On (page 133)

< Reg CMP Off. The

Timer1repeat (page 169)

Timer1 ON time

(page 169)

Timer1Duration (page 169)

settings are not important in this case.

AutoBatt

Engine starts when actual Battery voltage <

Batt undervolt (page 145)

Batt volt del

(page 145)

and stays running for

Timer1Duration (page 169)

. Function operates in AUT

mode.

AutoStop

Engine is switched from AUT to MAN and stopped or stopped from MAN mode (like by

STOP button) when engine runs longer then

Timer1Duration (page 169)

on actual RPM

less or equal

Idle speed (page 118)

+ 5 % (fix limit). Function is not active during engine

start.

Timer1Function

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 168 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: