ComAp InteliDrive FLX LITE Manual Download Page 141

Page: 141 / 228

ID-FLX Lite Global Guide

141

Comm object

8260

Related applications

Description

Limit for Warning Underspeed protection. Active protection is indicated as “Wrn Underspeed” in Alarm list.

Under speed Warning protection is inactive 5 s after RPM is over

Starting RPM (page 114)

and during the

Idle time.

The

is deactivated when Wrn underspeed protection is active and needs the

Fault reset for activation after RPM is over Underspeed limit.

back to List of setpoints

Setpoint group

Engine protection

Related FW

2.5.0

Range [units]

0 .. 600 [s]

Default value

Step

Comm object

12620

Related applications

Description

Engine is switched to Cooling state when Binary input FlowSwitch is not closed within Flow SwitchDel after

„Running“ (Ready to load) engine state activation.

Flow SwitchDel

back to List of setpoints

Setpoint group

Engine protection

Related FW

2.5.0

Range [units]

DISABLED, ENABLED [-]

Default value

Step

UnderspeedSd

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 141 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: