manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 121 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 121

ID-FLX Lite Global Guide

121

Setpoint group

Engine parameters

Related FW

2.5.0

Range [units]

0.0 .. 300.0 [s]

Default value

0.5

-

Step

0.1

Comm object

10525

Related applications

Description

This setpoint adjusts the Fuel solenoid output activation in relation to Starter output when Fuel solenoid =

GAS. Setpoint values mean that fuel valve is opened after the Starter. FuelSol offset has effect for both Fuel

solenoid = DIESEL or GAS.

Engine starting procedure when

Fuel solenoid (page 120)

= GAS

Note:

A new feature has been added which prolongs the last cranking attempt by 25% of MaxCrank time

with closed Fuel valve (Fuel Solenoid binary output) in order to ventilate the remaining gas, as is

implemented in IG/IS-NT. This function is valid only when

Fuel solenoid (page 120)

= GAS

Note:

Is modified functionality of the Ignition binary output. The Ignition binary output will close 1 second

(fixed value) after activation of binary output Fuel solenoid (when Fuel solenoid = GAS setting is active).

Generally, the output closes after reaching value of CrankRPM = 30RPM (fixed value). The output opens

after stopping of the engine or during crank fail pauses among crank attempts.

FuelSol offset

6

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments