manualshive.com logo in svg

ComAp InteliDrive FLX LITE, Manual, Page: 182 / 228

Share
Download
ComAp InteliDrive FLX LITE Manual Download Page 182

ID-FLX Lite Global Guide

182

Setpoint group

Act. Calls/SMS

Related FW

2.5.0

Range [units]

OFF, ON [-]

Default value

-

Step

-

Comm object

8484

Related applications

Description

Set this setpoint to YES if you want to get messages when a red (shutdown) alarm occurs.

Note:

The target address (cellular network phone number or e-mail address) must be set correctly to the

setpoint(s) TelNo/Addr Ch1 resp.

TelNo/Addr Ch1, 2 (page 182)

.

Red Alarm Msg

6

back to List of setpoints

Setpoint group

Act. Calls/SMS

Related FW

2.5.0

Range [units]

[-]

Default value

-

Step

-

Comm object

9597

Related applications

Description

Enter either a valid cellular network phone number or e-mail address to this setpoint, where the alarm

messages shall be sent. Type of active call is considered from the value of this parameter. If it consist „@“ it

is supposed to be e-mail address and active e-mail is sent. If the value is number, without „@“, it is

supposed to be the telephone number and active SMS is sent.

Note:

These setpoints can be modified from PC only!

For cellular network numbers use either national format (i.e. like number you will dial if you want to make

a local call) or full international format with "+" character followed by international prefix at the beginning.

TelNo/Addr Ch1, 2

6

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Reviews:

No comments