ComAp InteliDrive FLX LITE Manual Download Page 3

Page: 3 / 228

ID-FLX Lite Global Guide

4.6.3 IL-NT-RD Wiring

4.6.4 IGL-RA15 (EM2IGLRABAA, EM2FPCRAEAA)

4.7.4 Power supply fusing

4.7.5 Binary output protections

4.7.6 Magnetic pick-up

5 Controller setup

5.1 Analog inputs

5.1.1 Table of controller analog inputs

5.1.2 Table of analog inputs options

5.1.3 Connection of InteliDrive Lite analog inputs

5.1.4 Current output transducers

5.1.5 Analog input extension measurement

5.2 Binary inputs and outputs

5.3 Analog outputs

5.3.1 Default analog output curves

5.4 Remote modules - CAN bus connection

5.4.1 Connection rules

5.5 Front panel elements

5.6 Init screens

5.6.1 Init screen

5.6.2 Firmware screen

5.6.3 Languages screen

5.6.4 User Interface screen

5.7 Display menus

5.7.1 Switching between User and Engineer menus

5.8 How to select the engine mode?

5.9 How to view measured data?

5.10 How to view and edit setpoints?

5.10.1 How to change the display contrast?

5.10.2 How to check software revision?

5.10.3 How to check the serial number and choose interface?

5.10.4 How to change language?

5.11 How to find active alarms?

5.12 How to list History records?

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 3 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: