ComAp InteliDrive FLX LITE Manual Download Page 81

Page: 81 / 228

ID-FLX Lite Global Guide

Faultcode

Diagnostic code

Faultcode

Diagnostic code

0×6200

FanActuator

0×E200

OverheatProt

0×6400

WasteGateAct

0×E600

CoordEmergStop

0×6600

StarterActuatr

6.4 Tier 4 diagnostic codes

If the configured ECU supports Tier 4 standard, on the controller screen are displayed supplementary values

relative to the DPF status.

In ECU list-5.6 supported for John Deere, Cummins CM2250, CM850 and Deutz EMR4.

Table 6.1 Practical example of the screen

HEST Lamp

SPN 3698

Exhaust High Temperature.

Visible when SPN 3698 = 1

DPF Inhibit

SPN 3702

Visible when SPN 3702 = 1

DPF Lamp

SPN 3696

SPN 3697

Visible when CM1: SPN 3696 (Force switch) = 1

SPN 3697 (DPF Lamp Command) = 1.

Blinks – changes to inverse (1Hz) when 3697 =

100.

DPF Lamp

+ Warning

Active when 3697 = 1 and SPN 3701 = 4

Meaning of the pictograms

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 81 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: