Cisco FM1200 Volo Installation And Configuration Manual Download Page 62

Page: 62 / 175

Remember that all Cisco devices within a network

must

use the

same Prodigy version.

IMPORTANT

Prodigy 2.0 is

not

compatible with Prodigy 1.0. Do not

implement the two protocol versions within the same network.

If you are expanding an existing network using new Cisco
hardware components, make sure that all components are
compatible with each other by:

1. Upgrading all network components within the same

network to firmware version 6.5 or higher.

2. Configuring all network components within the same

network to operate using either Prodigy 1.0 or Prodigy
2.0.

Option 2 is recommended if the network does not contain older
Cisco devices that are not compatible with Prodigy 2.0.

If needed, change the unit's Prodigy version by clicking the

Prodigy 1.0

radio button or

Prodigy 2.0

radio button.

Save the Prodigy version settings by clicking the

Save

button.

Alternatively, clear the settings by clicking the

Reset

button.

Changing the LAN parameters

The LAN Parameters box (below) contains the entry controls for local-
address setting.

Device configuration using the configurator interface

Page 62 of 175

Summary of Contents for FM1200 Volo
















































































































































































Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands

Cisco FM1200 Volo, Installation And Configuration Manual

Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands