Cisco FM1200 Volo Installation And Configuration Manual Download Page 43

Page: 43 / 175

• The

Two Factor Authentication page

will be shown.

• The current two-factor authentication status of your portal

account will be shown near the top of the page.

Click the

Set Up Two Factor Authentication

button.

• A two-factor authentication dialog will ask to confirm your

identity. If the name and E-mail address shown in the
dialog are yours, enter your current portal password and
click the

Validate identity

button.

An E-mail will be sent to your E-mail address with a verification
code in the body of the mail. Enter the verification code in the

Verification code

field of the Two Factor Authentication web

page.

• The Two Factor Authentication web page will show a QR

code.

Use the authentication app on your mobile phone to scan the QR
code on the web page.

Figure 12 (page 43)

is a typical example

of the QR code you will be shown.

Figure 12. Two Factor Authentication (typical QR code)

• The authenticator app will generate an authentication code.

Enter this code in the

Authentication code

field of

the Two Factor Authentication web page, and click the

Enable Two Factor Authentication

button.

• A list of ten

recovery codes

will be shown on the Two

Factor Authentication web page. It is recommended that
you save these codes in case you lose your mobile phone.
Download the recovery codes as a *.TXT file by clicking
the

Download

button, or print a hard copy of the codes by

clicking the

Print

button.

6.3. Administering plug-in license codes

The Partner Portal Plug-ins page can be used to do the following tasks:

• Convert plug-in License codes to Activation codes

• Deactivate active plug-in License codes

Using the Cisco Partner Portal

Page 43 of 175

Summary of Contents for FM1200 Volo
















































































































































































Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands

Cisco FM1200 Volo, Installation And Configuration Manual

Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands