manualshive.com logo in svg

Cisco FM1200 Volo, Installation And Configuration Manual, Page: 59 / 175

Share
Download
Cisco FM1200 Volo Installation And Configuration Manual Download Page 59

7.4. General settings

7.4.1. The General Mode window

The General Mode window contains controls to monitor and/or change the
following settings:

• The unit's operational mode.
• The version of Prodigy currently being used by the unit.
• The unit's LAN parameters.
• If the local unit is in 

Bridge Mode

, the Bridge ID of the remote unit to

which the local unit must be linked.

To change the General Mode settings, do the following steps:

•

Click the 

-general mode

 link under 

GENERAL SETTINGS

 in the

left-hand settings menu (below).

Figure 23. Configurator GUI (General Mode)

• The 

GENERAL  MODE

  dialog  will  be  shown  (

Figure  23

(page 59)

).

Device configuration using the configurator interface

© 2021 Cisco and/or its affiliates. All rights reserved.

Page 59 of 175

Summary of Contents for FM1200 Volo
















































































































































































Reviews:

No comments