Cisco FM1200 Volo Installation And Configuration Manual Download Page 48

Page: 48 / 175

To use the Configurator interface to access the Cisco FM1200 Volo
directly, do the steps that follow:

Power ON the unit.

Wait approximately one minute for the boot sequence to
complete.

Connect one end of a CAT5/6 Ethernet cable to the computer that
will be used to configure the Cisco FM1200 Volo.

Connect the other end of the Ethernet cable to the

Console

LAN

port on the Cisco FM1200 Volo.

Manually set the computer's IP address and Netmask to be
recognizable by the Cisco FM1200 Volo. The correct settings are
as follows:

•

IP address:

192.168.0.10 (or any other IP address

belonging to subnet 192.168.0.0/255.255.255.0)

•

Netmask:

255.255.255.0

Launch the computer's web browser.

Enter the IP address of the Cisco FM1200 Volo in the browser's
URL entry field.

• If the Configurator interface is shown immediately, proceed

Step 9

below.

• Alternatively, you may see the following window:

Figure 13. 'Connection Not Private' warning (Google
Chrome)

Device configuration using the configurator interface

Page 48 of 175

Summary of Contents for FM1200 Volo
















































































































































































Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands

Cisco FM1200 Volo, Installation And Configuration Manual

Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands