Cisco FM1200 Volo Installation And Configuration Manual Download Page 119

Page: 119 / 175

Figure 49. Configurator GUI (VLAN SETTINGS dialog)

Connect the unit to a VLAN that is part of the local wireless
network by checking the

Enable VLANs

check-box.

Check the

Enable VLANs

check-box.

Enter the management identification number of the VLAN (used
to communicate with the device's operating system) in the

Management VLAN ID:

field.

NOTE

The same Management VLAN ID must be used on all
Cisco devices that are part of the same mesh
network.

Enter the native identification number (the VLAN ID implicitly
assigned to untagged packets received on trunk ports) in the

Native VLAN ID:

field.

Save the VLAN settings by clicking the

Save

button. Alternatively,

clear the settings by clicking the

Reset

button.

Rules for packet management

Parameter

Default value

Default VLAN configuration

The factory-set VLAN parameters for the unit are as follows:

Management VLAN ID (MVID)

Native VLAN ID (NVID)

Native VLAN processing

Enabled

Port mode (all Ethernet ports)

Smart

Traffic classes

The system classifies incoming data packets according to the following definitions:

Signaling

Ethernet protocol type $8847 or $09xx

User

All other traffic

Device configuration using the configurator interface

Page 119 of 175

Summary of Contents for FM1200 Volo
















































































































































































Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands

Cisco FM1200 Volo, Installation And Configuration Manual

Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands