Cisco FM1200 Volo Installation And Configuration Manual Download Page 24

Page: 24 / 175

4. Installing the radio

4.1. Installing the radio using the multi-axis mounting
bracket

IMPORTANT

The FM Ponte transceiver kit includes two multi-axis mounting
brackets (Cisco part number

FM-BRKT

The FM1200 Volo transceiver kit includes a single

FM-BRKT

mounting bracket.

The

FM-BRKT

mounting kits do not need to be purchased

separately.

The diagram below shows the components and assembly sequence for
installing the radio using the Cisco multi-axis mounting bracket.

The table below shows the components and quantities of each component
used in each FM-BRKT assembly:

Component number

Description

Quantity

Pole Mount

Swivel Rod

Radio transceiver

U-bolt

Installing the radio

Page 24 of 175

Summary of Contents for FM1200 Volo
















































































































































































Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands

Cisco FM1200 Volo, Installation And Configuration Manual

Search results

Summary of Contents for FM1200 Volo

Reviews:

Related manuals for FM1200 Volo

Brands by name

Popular brands