Circontrol Raption 50 Series User Manual Download Page 96

Page: 96 / 168

Raption 50 Series User Manual

1. Remove the SIM card cover.

2. Gently slide the card into the slot in the connector until it stops.

3. Replace the SIM card cover.

After installing the SIM card, check out that the 3G antenna (mobile) and the power
connector are properly attached.

NOTE:

SIM card is not provided with equipment.

4 — LO G G I N G I N

Plug again the power supply for the modem.

NOTE:

After plugging back the modem, it can take until 5 minutes to respond.

3G modem configuration is performed using the Ethernet interface. Connect your
Service PC using an Ethernet cable as shown in the following image:

Set the IP number

192.168.13.50

on your laptop, following the previous Chapter

‘4-D’

-->

-LAN Connection procedure -

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands