Circontrol Raption 50 Series User Manual Download Page 128

Page: 128 / 168

124

Raption 50 Series User Manual

The IP address assigned in the chapter 5, will be useful to connect with the Charge
Point in order to monitor the real-time status.

The main way to connect is using the

CirCarLife client software

(Supplied by

Circontrol PS-Support staff) or you can download from:

http://circarlife.com/en/downloads/

NOTE:

Java software needs to be installed on your computer in order to run the client

software, please, download last version from: www.java.com

In remote connections, where is required communicate via
3G/4G data with the Charge point in order to monitor its
parameters, it should be noted that there will be a HIGH
consumption of data.

In the case of doing the Charge point monitoring, it is
reccommended to use Ethernet communications via internet
(see chapter 4-D).

Introduction

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands