Circontrol Raption 50 Series User Manual Download Page 14

Page: 14 / 168

Raption 50 Series User Manual

The Charge Point is equipped with three connectors of different load; these can
recharge a large range of vehicles:

• AC (Mode 3): Type 2 tethered cable (63A/44kW) or Type 2 socket (32A/22kW)*

• DC (Mode 4): CHAdeMO, Tethered cable, 3m. Until 125 A / 50 kW

• DC (Mode 4): Combo 2 (CCS), Tethered cable, 3m. Until 125 A / 50 kW

(*) Depending of the model, the components can vary.

Connectors

The following considerations, before using this Charge Point, must be considered.

Of the three types of charges that the Charge Point can perform, it can carry out:

• Only AC

• Only DC CHAdeMO

• Only DC CCS 2

• Simultaneous, AC and one DC connector at the same time

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands