background image

120

Raption 50 Series User Manual

Value

Description

Authorization 
cache enabled

YES:

 maintain a local list of all presented identifiers that have 

been successfully authorized by the Central System.

NO: 

authorization for presented identifiers is requested directly 

to the Central System

Authorize remote 
Tx requests

YES:

 the Charge Point asks for authorization when the Central 

System sends a remote start

NO: 

the Charge Point starts the Charge Transaction when the 

Central System sends a remote start

Local pre-
authorize

YES: 

Charge Point looks for locally-authorized identifiers without 

waiting for the Central System authorization.

NO: 

Charge Point requests authorization for presented 

identifiers to the Central System.

Allow offline Tx for 
unknown Id

YES:

 during offline period unknown identifiers are allowed to 

start charging

NO: 

during offline period unknown identifiers are NOT allowed to 

start charging

Local authorize 
off-line

YES: 

during offline period locally-authorized identifiers are 

allowed to start charging

NO: 

during offline period locally-authorized identifiers are NOT 

allowed to start charging

Stop transaction on 
invalid Id

YES:

 

stop existing Charge Transaction after response from 

Central System when user is blocked, expired or invalid.

NO

:

 Charge Transaction does not stop even if backend rejects the 

user.

Summary of Contents for Raption 50 Series









































































































































































Reviews: