Circontrol Raption 50 Series User Manual Download Page 135

Page: 135 / 168

131

Option

Description

Displays the previous view.

Displays the next view (If available).

Devices

Device list shortcut.

Graph

Creates a graph about the charging session.

Table

Creates a table about the charging session.

Events

Displays event history.

Properties

Displays the properties window of the current view.

Allows us to print the current view.

2 — T O O L B A R

Toolbar contains the most frequent options used in the CirCarLife client software.

It is possible to hide or display buttons for the toolbar. Doing right-click on the toolbar
and following setup menu will appear:

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands