Circontrol Raption 50 Series User Manual Download Page 95

Page: 95 / 168

Network LED

This monitors the cellular network.

•

Red:

No cellular network is present or the device is in radio passthru mode. (There

is no network coverage at the location.)

•

Flashing red:

The device is attempting to connect to the cellular network.

•

Yellow:

The cellular network is found and the device is connecting.

•

Flashing yellow:

The cellular network is unavailable. (The device was unable to

authenticate on the network.)

•

Green:

Connected to the cellular network.

•

Flashing Green:

The device is roaming.

3 — S I M CA R D I N S TA L L AT I O N

Explanation of SIM card installation:

Disconnect the power supply for modem and insert the SIM card which was given by
your ISP (Internet Service Provider).

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands