Circontrol Raption 50 Series User Manual Download Page 134

Page: 134 / 168

130

Raption 50 Series User Manual

Option

Description

Toolbar

Displays or hides the toolbar.

Statusbar

Displays or hides the status bar.

Alarm ...

Visual and audible alarm if communication is lost
between Charge Point and computer connected.

Internal toolbar

Not available tab.

Event actions

List of actions enabled in the CirCarLife software.

Time zone

It lets to change the time over GMT.

Connect

Connects with the Charge Point monitored.

Language

Changes the CirCarLife client software language.

Graphs properties

Changes graph appearance.

About

Displays client application version information.

General:

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands