Circontrol Raption 50 Series User Manual Download Page 13

Page: 13 / 168

Status Beacon lights

Over each connector there is a beacon light, it indicates the state of charge in which
the socket/connector is located.

Colour

Status

Description

Green

Available

The connector or socket is available to start a charging
session

Blue

Charging

The connector or socket is performing a charging session

Cyan

Booked

(OCPP 1.5)

The connector or socket has been booked by system
operator through OCPP

Red

Error

The Charging Station indicates that the emergency button
has been activated or some error has occurred. Check the
HMI Screen and follow the instructions

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands