Circontrol Raption 50 Series User Manual Download Page 105

Page: 105 / 168

101

Configuration

Go to the

Setup Webpage

‘Integrations’

tab

Once OCPP 1.5 option is selected, a link appears allowing access to the OCPP
configuration.

Please, click on the link button as shown in the picture:

New tabs are opened to show OCPP Settings. It can also be accessed directly typing:
http://

:8080/html/setup.html

These tabs require a user identification:

User: admin

Password: 1234

First time is running the integration selected on the Charge Point, it starts as
configuration mode and all fields are empty.

Settings are always stored even when the Charge Point is powered off or even the
integration is disabled/stopped.

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands