Circontrol Raption 50 Series User Manual Download Page 37

Page: 37 / 168

Connectors status

The HMI screen shows a different symbols over the connector pictures, as you can see
below:

- It means that there is not any problem in this connector and
is ready for use.

- This connector is out of service for any technical reason.
Press over

‘Information’

touch button in order to get more

information about it.

- The Charge Point is out of service because the emergency
button has been pressed. This fact affects all the connectors
at the same time.

- The connector is disabled. The Charge Point is out of order
due to some maintenance job or because the Back office has
decided to stop it.

Summary of Contents for Raption 50 Series









































































































































































Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands

Circontrol Raption 50 Series, User Manual

Search results

Summary of Contents for Raption 50 Series

Reviews:

Related manuals for Raption 50 Series

Brands by name

Popular brands