background image

THROW DISTANCE 

D-2 

Roadie 25K User’s Manual

 

Table D.1. Throw Distance Formulas 

Lens Throw Ratio 

Throw Distance Formula (cm) ±5% 

Min. Throw Distance 

Approx. Max.Screen Width (

1:1 fixed 

1.03 x screen width (

 cm) + 28.3 

5m (15 ft.) 

44m (145 ft.) 

1.25 – 1.45:1 zoom 

Min:1.26 x screen width (

 cm) + 25.9 

Max: 1.46 x screen width (

 cm) + 23.5 

5m (15 ft.) 

44m (145 ft.) 

1.45 – 1.8:1 zoom 

Min: 1.45 x screen width (

 cm) + 18.4 

Max: 1.81 x screen width (

 cm) + 16.8 

5m (15 ft.) 

44m (145 ft.) 

1.8 – 2.4:1 zoom 

Min: 1.80 x screen width (

 cm) + 17.9 

Max: 2.41 x screen width (

 cm) + 15.1 

5m (15 ft.) 

44m (145 ft.) 

2.2 – 3.0:1 zoom 

Min: 2.24 x screen width (

 cm) + 9.6 

Max: 3.05 x screen width (

 cm) + 4.0 

5m (15 ft.) 

44m (145 ft.) 

3.0 – 4.3:1 zoom 

Min: 3.05 x screen width (

 cm) + 2.5 

Max: 4.35 x screen width (

 cm) + .04 

5m (15 ft.) 

44m (145 ft.) 

4.3 – 6.0:1 zoom 

Min: 4.37 x screen width (

 cm) + 7.3 

Max: 6.16 x screen width (

 cm) + 3.0 

9m (30 ft.) 

44m (145 ft.) 

5.5 – 8.5:1 zoom 

Min: 5.59 x screen width (

 cm) + 10.1 

Max: 8.71 x screen width (

 cm) + 1.2 

9m (30 ft.) 

44m (145 ft.) 

NOTES: 1) Make sure to use HORIZONTAL screen width in all formulas. 2) Throw distance can often be exceeded with negligible 
loss of focus. 3) Throw ratios, formulas and throw distances apply to both standard and optional high-contrast lenses. 

 

Based on the formulas provided in Table D.1, a selection of pre-calculated throw 
distances for each lens type appears in the charts on the following pages. Refer to 
these examples to quickly determine a proper throw distance (±5%) for your 
installation and lens, or to determine what zoom range of image size is possible at a 
given throw distance. 

Keep in mind that ambient light, screen material, lamp size, image content and other 
variables at your site may affect whether or not a given throw distance—and resulting 
image size—will be ideal for your installation. 

NOTE: Throw ratios, formulas and throw distances apply to both standard and 
optional high-contrast lenses. 

 

 

Throw Distance Tables 

'

Summary of Contents for Roadie 25K
































































































































































































Reviews: