Canon imageRUNNER ADVANCE C2225 Basic Operation Gude Download Page 90

Page: 90 / 180

Pull out the waste toner container from the left rear side of the machine .

1.■ Open■the■cover■for■the■waste■toner■

container.

2.■ Pull■out■the■waste■toner■container.

Back Left Side of the Main Unit

Attach the provided cover to the used waste toner container .

1.■ Remove■the■cover■from■the■used■

waste■toner■container.

2.■ Cover■the■opening■of■the■used■waste■

toner■container■with■the■cover■

removed■in■step■1.

When removing the waste toner container, be careful not to tilt it, as the toner may spill and get

onto your hands or clothing .

Put the removed waste toner container into a bag, and then tie it up at the top

to prevent the toner remaining inside the cartridge from scattering .

Use a bag in the box in which the new waste toner container is stored.

Summary of Contents for imageRUNNER ADVANCE C2225





















































































































































































Search results

Summary of Contents for imageRUNNER ADVANCE C2225

Reviews:

Brands by name

Popular brands

Canon imageRUNNER ADVANCE C2225, Basic Operation Gude

Search results

Summary of Contents for imageRUNNER ADVANCE C2225

Reviews:

Brands by name

Popular brands